Browsing by Author "Bor, Sakir"

Now showing 1 - 3 of 3

Enhanced Sintering of Tini Shape Memory Foams Under Mg Vapor Atmosphere
(Springer, 2012) Aydogmus, Tarik; Bor, Sakir
TiNi alloy foams are promising candidates for biomaterials to be used as artificial orthopedic implant materials for bone replacement applications in biomedical sector. However, certain problems exist in their processing routes, such as formation of unwanted secondary intermetallic phases leading to brittleness and deterioration of shape memory and superelasticity characteristics; and the contamination during processing resulting in oxides and carbonitrides which affect mechanical properties negatively. Moreover, the eutectic reaction present in Ti-Ni binary system at 1391 K (1118 A degrees C) prevents employment of higher sintering temperatures (and higher mechanical properties) even when equiatomic prealloyed powders are used because of Ni enrichment of TiNi matrix as a result of oxidation. It is essential to prevent oxidation of TiNi powders during processing for high-temperature (> 1391 K i.e., 1118 A degrees C) sintering practices. In the current study, magnesium powders were used as space holder material to produce TiNi foams with the porosities in the range of 40 to 65 pct. It has been found that magnesium prevents secondary phase formation and contamination. It also prevents liquid phase formation while enabling employment of higher sintering temperatures by two-step sintering processing: holding the sample at 1373 K (1100 A degrees C) for 30 minutes, and subsequently sintering at temperatures higher than the eutectic temperature, 1391 K (1118 A degrees C). By this procedure, magnesium may allow sintering up to temperatures close to the melting point of TiNi. TiNi foams produced with porosities in the range of 40 to 55 pct were found to be acceptable as implant materials in the light of their favorable mechanical properties.
Phase Transformation Behavior of Porous Tini Alloys Produced by Powder Metallurgy Using Magnesium as a Space Holder
(Springer, 2011) Aydogmus, Tarik; Bor, Elif Tarhan; Bor, Sakir
Porous TiNi alloys with porosities in the range of 51 to 73 pct were prepared successfully applying a new powder metallurgy fabrication route in which magnesium was used as a space holder, resulting in either single austenite phase or a mixture of austenite and martensite phases dictated by the composition of the starting powders, but entirely free from secondary brittle intermetallics, oxides, nitrides, and carbonitrides. Since transformation temperatures are very sensitive to composition, deformation, and oxidation, for the first time, transformation temperatures of porous TiNi alloys were investigated using chemically homogeneous specimens in as-sintered and aged conditions eliminating secondary phase, contamination, and deformation effects. It was found that the porosity content of the foams has no influence on the phase transformation temperatures both in as-sintered and aged conditions, while deformation, oxidation, and aging treatment are severely influential.
Superelasticity and Compression Behavior of Porous Tini Alloys Produced Using Mg Spacers
(Elsevier, 2012) Aydogmus, Tarik; Bor, Sakir
In the scope of the present study, Ni-rich TiNi (Ti-50.6 at %Ni) foams with porosities in the range 38-59% were produced by space holder technique using spherical magnesium powders as space formers. Single phase porous TiNi alloys produced with spherical pores were subjected to loading-unloading cycles in compression up to 250 MPa stress levels at different temperatures in as-processed and aged conditions. It has been observed that strength, elastic modulus and critical stress for inducing martensite decrease with increasing porosity. Partial superelasticity was observed for all porosity levels at different test temperatures and conditions employed. Irrecoverable strain was found to decrease with pre-straining and with increasing test temperature. Unlike in bulk TiNi alloys a constant stress plateau has not been observed during the compression testing of porous TiNi alloys. Instead linear superelasticity with a quite steep slope allowing 5% applied strain to be recovered after pre-straining or aging was observed. Even at test temperatures higher than austenite finish temperature in as-sintered and aged condition, strain applied could not be recovered fully. due to martensite stabilization resulting from heavy deformation of macro-pore walls and sintering necks. TiNi foams produced with porosities in the range of 38-51% meet the main requirements of biomaterials in terms of mechanical properties for use as bone implant. (c) 2012 Elsevier Ltd. All rights reserved.